Technical Papers
Click on titles below to see PDF file of technical paper presentation.
Wednesday 15-NOV-00
Thursday 16-NOV-00
|
Automotive |
Non-Automotive |
CAD-Embedded |
|
| 1 | Suspension
Development with a Small Vehicle J. Arbiol, A. Catala, IDIADA |
Virtual
Prototyping in Ship Design M. Raffa, R. Costa, Fincantieri S.p.A., A. Zini, A. Rocca, Cetena S.p.A. |
CAD Welcome Address CAD embedded ADAMS future |
| 2 | Case
Studies of Fatigue Life Prediction of Spot Welded Car Bodies P.Heyes, nCode & M. Sharp, MTS |
Aircraft
Engine Analysis Using ADAMS D. Riesland, MDI |
|
| 3 | Visteon's
Approach to All-Wheel DriveVehicle Dynamics Model Simulation and
Correlation V. Subramanyam, V.Monkaba, T. Alexander, Visteon |
Ariane
4 Payload Fairing Separation Assessment R. Lagier, Arianespace, T. Bernard, MDI France |
|
| 4 |
ADAMS/Car for Motorsports Applications |
Rollover stability of Tank Vehicles |
|
| 5 | Response
surface modeling technique adopted to ADAMS suspension equilibrium
analysis Y. Sakai, Nissan |
A
Highly Efficient, General-Purpose Approach for Co-Simulation with
ADAMS A. Elliott, MDI |
SDRC
I-DEAS: Loads evaluation for an helicopter flight control system G. Millilotti, AGUSTA |
| 6 | Powertrain
Dynamics Applications using "ADAMS/Engine powered by FEV": Part
I: Flexible Valve Springs C.Ortmann & H.Skovbjerg, MDI |
Functional
Design and Kinematic Synthesis of a Chain Driven High-Speed Packaging
Machine R. Borsari, F. Dunge Tetra Brik Packaging Systems S.p.A. |
SDRC
I-DEAS: Flexibility effects on precision for a steelwire electrowelding machine M. Cagliari, Pittini, Impianti Industriali |
| 7 | Powertrain
Dynamics Applications Using "ADAMS/Engine powered by FEV": Part
II:Cranktrain Dynamics M.Rebbert & P.Kley, FEV |
Concepts
Evaluation of a Voluntary Milking Robot System J. Johansson, Stockholm Royal Institute of Technology |
SDRC
I-DEAS: The simulation of a self-adhesive labelling station swinging tensioning arm S. Grassi, Kosme |
| 8 |
Four Post Testing and Simulation for Optimization
of Race Car Vehicle Dynamics |
Kinematical
Synthesis and Dynamical Analysis of Multilink Robot Using Multi
Body Approach |
Solid
Works: |
| 9 | Transmission
Simulation with ADAMS - Gear Module for ADAMS and Interface to ECS
Software GESIM J. Leitner, Steyr-Daimler Puch |
Design
of a High Speed Low Friction XY-table A.F. Bakker, Philips Centre For industrial Technology (CFT) |
PTC
Pro/E: Integration of ADAMS in the CAD Environment for the Automatic Packaging Machines Industry V. Fiorini, CAE Dept., G.D. Spa |
| 10 | Predicting
Service Life of Transit Bus G.Ashdown, Orion Bus J.Sharp, S.McEllan, D.Nelson, MDI |
Analysis
of an Emergency Brake Device and its Effects on the Passengers of
an Amusement Ride Machine G. Manara, Zamperla Spa |
Solid
Edge: Dynamic Designer in Solid Edge MDI |
| 11 | Integration
of Virtual and Physical Prototype Testing Bill Bigot, MTS |
Study
of Driveline Functionality during Off-road Driving of an Articulated
Hauler H. Illerhag, Volvo Articulated Haulers AB, F. Sjögren, MDI AB |
Unigraphics: High Speed Assembly Machines in UG/Mechanisms 3M - MDI |
| 12 | Influence
of Parameters on Vehicle Roll-over G. Scholpp, J. Schmidt, M. Frimberger, F. Wolf, Siemens AG |
Controlled electrohydraulic vehicle using
ADAMS/Car, ITI-sim and MATLAB/Simulink S.Frediani, G.Faustini,
Fiat Research |
Unigraphics: |
| 13 | Study
about the Shimmy-Effect on a McPherson front Axle R. Thorsten, Phoenix Vibroacustic GmbH |
Moving
Load Modeling on Flexible Body T. Mochizuki, ESTECH |
Abrico,
Virtual Prototyping Tool for the Design of Gearbox Llinkages, Based
on CATIA and ADAMS M. Furstoss, Peugeot |
| 14 | Simulation
of Metal Pushing Type V Belt for CVT K. Kanokogi, Honda |
State
of Sress Evaluation of Mechanical Components by Modal Synthesis C. Braccesi, F. Cianetti, Univ of Perugia, F. Ambrogi, MDI |
Autodesk
MD: Kinematic Analysis of a Seeding Drill Machine Orienta-Mum |
| 15 | Simulation
of the Vehicle-Dynamic in the Development Process M. Pausch, G. Prokop, Audi |
Dynamical
Analysis of Human Walking M. Wojtyra, Warsaw Univ of Technology |
Autodesk
MD: Kinematic Analysis of Ottogalli-Businaro Forming Press Mum |
| 16 |
Simulation
of Moving Parts on Flexible Bodies Using Multibody Approach. Case
Test on a Reinforced Concrete Highway Bridge |
ADAMS
Solution Improve Process, Product, Profit, Prestige |
Autodesk
MD: |
Friday 17-NOV-00
| CAD-Embedded Technical Papers |
|
| 1 | Solid
Works: induDrive Cam Disc Optimization w/ Dynamic Designer Motion
InduSIM |
| 2 | Solid
Works: Theme Park applications of Dynamic Designer
Cook Engineering |
| 3 | Solid
Works: Cam Driven Automatic Fitting Machine Simulation w/ Dynamic
Designer/Motion in SolidWorks Keber |
| 4 | CoCreate
Solid Designer: Synthesis and Analysis of a Cam System for Labelling
Automatic Machines C. Antonioli, PE Labellers |
| 5 | CoCreate
Solid Designer: Automatic Packaging Machine Design C. Zagnoni, TMC |
| 6 | CoCreate
Solid Designer: Manipulator for Mechanical Arm Ognibene, Manitou |
| 7 | SDRC
I-DEAS: Sofa Bed Mechanism Simulation and optimization N. Spontella, Styling |
| 8 | SDRC
I-DEAS: Load Prediction and Stress Evaluation of a Deviator Mechanism
for rolling-mill Machine M. Zuanella, Studio Zuanella |
