Keyword | Comments | Pages |
ADAPTIVE (w) | ||
ANISOTROPIC (r/w) (Mechanical) | ||
ANISOTROPIC (r/w) (Thermal) | ||
ARRUDABOYCE (r/w) | ||
ATTACH EDGE (w) | ||
ATTACH ELEMENT (w) | ||
ATTACH FACE (w) | ||
ATTACH NODE (w) | ||
AXITO3D (w) | Marc 2003 only. Uses PRE STATE otherwise. | |
BUCKLE INCREMENT (w) | ||
CHANGE STATE (w) | ||
COMPOSITE (w) | ||
CONNECTIVITY (r/w) | ||
CONTACT (r/w) | ||
CONTACT NODE(w) | ||
CONTROL (w) (Stress) | ||
CONTROL (w) (thermal analysis) | ||
COORDINATES (r/w) | All nodes are written relative to the global coordinate system except if the CYLINDRICAL keyword is used. | |
CRACK DATA (w) | ||
CREEP (r/w) | ||
CURVES (w) | ||
CYCLIC SYMMETRY(w) | ||
CYLINDRICAL (r/w) | For nodes listed in this option, nodal input (COORDINATES) and output (displacements, etc.) are given in this coordinate system. | |
DAMAGE (w) | ||
DAMPING (r/w) | ||
DEFINE (sets) (r/w) | ||
DENSITY EFFECTS (w) | ||
DIST FLUXES (r/w) | ||
DIST CHARGE (w) | Must use Table format | |
DIST CURRENT (w) | Must use Table format | |
DIST LOADS (r/w) | Can not put load on 1D elements. | |
END OPTION (w) | Written automatically. | |
ERROR ESTIMATES(w) | ||
EXCLUDE(w) | ||
FAIL DATA (r/w) | UFAIL not currently supported. Currently only one failure criteria supported. | |
FILMS (r/w) | Film coefficient and sink temp index not supported. | |
FIXED ACCE (r/w) | ||
FIXED DISP (r/w) | ||
FIXED EL-POT (w) | Must use Table format | |
FIXED TEMPERATURE (r/w) | ||
FIXED VOLTAGE (w) | Must use Table format | |
FOAM (r/w) | ||
FORMING LIMIT (w) | ||
GAP DATA (w) | ||
GASKET (w) | ||
GENT (r/w) | ||
GEOMETRY (r/w) | ||
GLOBALLOCAL (w) | Marc 2005 or higher. | |
GRAIN SIZE(w) | ||
HYPOELASTIC (w) | ||
INITIAL DISP (w) | ||
INITIAL PC (w) | ||
INITIAL POROSITY(w) | ||
INITIAL STATE (r/w) | ||
INITIAL TEMP (w) | Only one degree-of-freedom supported. | |
INITIAL VEL (w) | ||
INITIAL VOID RATIO (w) | ||
INSERT (w) | ||
ISOTROPIC (r/w) (Stress) | ||
ISOTROPIC (r/w) (Heat Transfer) | ISOTROPIC,THERAL used for Joule heating. | |
ISOTROPIC,ELECTROSTA (r/w) (Electrostatic) | Must use Table format | |
HYPOELASTIC (w) | Requires use of user subroutines. | |
LOADCASE (w) | ||
MASSES (w) | ||
MATERIAL DATA (w) | ||
MODAL INCREMENT (w) | ||
MOONEY (r/w) | ||
NO PRINT (w) | ||
NODAL THICKNESS (w) | ||
OGDEN (r/w) | ||
OPTIMIZE (w) | ||
ORIENTATION (r/w) | ||
ORTHO TEMP (r/w) | ||
ORTHOTROPIC (r/w) (Mechanical) | ||
ORTHOTROPIC (r/w) (Thermal) | ||
PHI-COEFFICIENTS (r/w) | ||
POINT FLUX (w) | Only one degree-of-freedom supported. | |
POINTS (w) | ||
POINT CHARGE (w) | ||
POINT CURRENT (w) | ||
POINT LOAD (r/w) | ||
POINT TEMP (w) | ||
POST (w) | ||
POWDER (w) | ||
PRE STATE (w) | Marc 2005 or higher. | |
PRINT ELEMENT (w) | ||
PRINT NODE (w) | ||
PROPORTIONAL INCREMENT (w) | ||
RBE2 (w) | ||
RBE3 (w) | ||
REAUTO (w) | ||
REBAR (w) | ||
RELATIVE DENSITY (w) | ||
RESPONSE SPECTRUM (w) | ||
RESTART (w) | ||
RESTART LAST (w) | ||
ROTATION A (w) | ||
SCALE (w) | Only for Small Strains, Small Displacement - Static analysis. | |
SERVO LINK (w) | Explicit MPCs and Sliding Surfaces defined by this keyword option. | |
SHAPE MEMORY(w) | ||
SHIFT FUNCTION (w) | ||
SOIL (w) | ||
SOLVER (w) | ||
SPECIFIC WEIGHT (w) | ||
SPLINE (w) | ||
SPRINGS (r/w) | ||
SURFACES (w) | ||
STRAIN RATE (r/w) | ||
TABLE (w) | Only writen for Marc 2003 or higher. | |
TEMPERATURE EFFECTS (r/w) | ||
THERMAL CONTACT (w) | See CONTACT. | |
TRANSFORMATION (w) | Displacement and loads or reactions are output relative to the transformed systems for the specified nodes. Transformations should not be applied to nodes that can come into contact with either a rigid or deformable body. | |
TYING (w) | Support for types 1-6, 26, 31, 32, 33, 34, 49, 50, 52, 53, 80, 100, and 102-506. TRANSFORMATION not recommended for nodes involved in TYING types. | |
UCONTACT (w) | ||
UFRIC (w) | ||
UHTCOE (w) | ||
UHTCON (w) | ||
UMOTION (w) | ||
UORIENT (w) | ||
VELOCITY (w) | ||
VIEW FACTOR (w) | ||
VISCEL EXP (r/w) | ||
VISCELMOON (r/w) | ||
VISCELOGDEN (r/w) | ||
VISCELORTH (r/w) | ||
VISCELPROP (r/w) | ||
WORK HARD (r/w) |