Company:

HorsePower Hannover e.V.

Products:

Adams
Adams Car

Industries:

Automotive
Motorsports

Formula Student Team Relies on Multibody Dynamics Simulation

Overview:
  • Adjust suspension design of an electric racecar
  • Model validation with the help of test curves
  • Simulate the Formula Student competition test situation

 
pdf iconDOWNLOADdown arrow

Company:

EDAG, voestalpine, and Simufact

Products:

Simufact
Simufact Additive

Industries:

Automotive

LightHinge+: Additively manufactured hood hinge

Overview:

In a common innovation project called LightHinge+, EDAG Engineering, voestalpine Additive Manufacturing Center and Simufact Engineering jointly developed a new hood hinge. The project team used the extended possibilities of additive production in order to re-think the component, to re-construct it and subsequently to manufacture it additively. As a result, the new hinge was built with 50% weight reduction compared to the original part, and with the additional advantage to have nearly the entire pedestrian protection functionality integrated within one part. It takes fewer component parts and less assembly steps to build the new hood hinge.

The design was done supported by topology optimization, which finally led to a bionic-like extremely filigree and lightweight structure. Such parts can only be reasonably produced by utilization of AM technology.


 
pdf iconDOWNLOADdown arrow

Company:

McMaster University

Products:

Actran Acoustics

Industries:

Automotive

Actran Induces Optimization of Electric Motor Drive Design

Overview:

The transportation industry is facing various new technological changes. Among them, the replacement of traditional internal combustion engines by electric powertrains makes new vehicles quieter. Still, new challenges in noise and vibration are rising, in particular during the design of electric motors. In order to develop efficient architectures meeting the expectations both in terms of performance and acoustic comfort, engineers need to access new methods and tools.

Motor design generally starts with the torque as the main purpose of an electric motor is to deliver the required torque at a given speed range. Then, the dimensions of the motor start becoming apparent and efficiency analysis, radial force analysis, structural analysis, and acoustic analysis enter the loop.

“Acoustics analysis should be part of the process and not applied at the end of it” explains Dr. Berker Bilgin, Research Program Manager and Chief Engineer of Canada Excellence Research Chair in Hybrid Powertrain program at McMaster University. If not, it will become difficult to reduce acoustic noise from the motor once the motor design is finalized. Electric motor noise is mainly due to the impact of electromagnetic radial forces (see Figure 1) that excite the stator structure.

Results Validation:

By including Actran in their design process, McMaster researchers developed current control techniques to limit acoustic noise: “Without making any changes in the motor we can actually reduce the acoustic noise just by optimizing the current, because the radial forces are also related to stator excitation, and we experimentally verified drastic noise reduction in switch reluctance motors”, said Dr. Berker Bilgin.

The use of simulation tools has reduced significantly the cost of prototyping and allowed a more advanced analysis of the designed product. Another added value of simulation is of course the attention paid to details thanks to 3D acoustic modelling capabilities. In addition, Actran’s visualization capabilities offer a great possibility for students to train and dig deeper in their research.

In the future, CERC in Hybrid Powertrain team plan on working on how to modify the structural modes without affecting the torque performance of the motor, focusing on current controls of the motors, or modelling the damping ratio of the motor for accurate estimation and reduction of acoustic noise in electric motors.


 
pdf iconDOWNLOADdown arrow

Company:

Safran

Products:

Simufact
Simufact Additive

Industries:

Aerospace

Safran: Collaborative Simultaneous Engineering Tool for Additive Manufacturing

Overview:

One of the manufacturing processes in which Safran Additive Manufacturing is more specifically interested in, is the Laser Beam Melting (LBM) process. The simulation of this process aims at identifying issues associated with part distortion during the manufacturing process, as well as the potential risks of failure of the part and its supporting structure. Safran called on MSC Software, which offers a solution that uniquely covers the entire manufacturing process, from the initial melting step of the part to the completion of a final HIP treatment (Hot Isostatic Pressing), including all post-processing operations such as a stress-relaxation heat treatment, baseplate cutting and supports removal. This solution is Simufact Additive.

Results Validation:

Safran Additive Manufacturing has taken full advantage of the added value of the Simufact Additive solution in order to secure the integration of the additive manufacturing processes into its “product-process” development processes, both upstream during product design and downstream for the production launch.

Safran Additive Manufacturing is now focusing on extending the use of the Simufact Additive solution to different types of parts and different grades of material, in order to improve the design process for additive manufacturing as a whole. MSC Software supports Safran Additive Manufacturing and the Group in achieving this objective through this solution that integrates into the global additive manufacturing value chain, ensuring a quality and open digital continuity.

Benefits:

The use of Simufact Additive has enabled us to save considerable time in production preparation thanks to the predictive nature of the software, which limits development by manufacturing iterations by using virtual development upstream, but also during the part design phase, by enabling us to anticipate the effects and limitations of the process at the product design level.

One of the added values of the Simufact Additive solution is that it allows us to bring together two activities: engineering and production. On the one hand, people from engineering who design parts with a strong focus on part performance in service, and, on the other hand, the methods office who master the industrial processes and its associated constraints. Simufact Additive is a solution well adapted to simultaneous engineering that facilitates dialogue between the different business activities involved in the same project. In addition, the software is easy to use, with an intuitive, business-oriented interface that allows for quick and easy appropriation/ownership.


 
pdf iconDOWNLOADdown arrow

Company:

Hyundai Motor Company

Products:

Actran Acoustics

Industries:

Automotive

Actran Helps Reduce Time to Optimize Design of Active Pedestrian Alerting System by 50%

Overview:

At moderate to high speeds, the only external noises typically generated by electric vehicles are caused by wind resistance or tire noise. As a consequence, electric vehicles present a risk to pedestrians and cyclists, especially those who are visually or hearing impaired or listening to headphones.

Hyundai active pedestrian alerting system Regulations have been issued in both the United States and the European Union requiring that newly manufactured electric vehicles make an audible noise when traveling at low speeds. These regulations have differing requirements for the amplitude and frequency content of the warning sound.

Results Validation:

The simulation results were validated by conducting a 1-volt sine sweep test for both the actual speaker and the simulations. As shown in the figure above, the spectral behavior of sound at 1 meter from the speaker predicted by simulation matches the physical measurements nearly perfectly.

By using Actran to optimize cavity and duct resonances, Hyundai engineers were able to design the speaker to handle low, mid and high frequencies as needed to meet both US and EU regulations while at the same time minimizing speaker size and power consumption. “The simulation results provided by Actran were much more comprehensive than information generated by physical testing, which helped Hyundai engineers quickly iterate to an optimized design in about half the time that would have been required using traditional build and test methods,” Lee said.


 
pdf iconDOWNLOADdown arrow

Company:

Major automotive OEM

Products:

Digimat

Industries:

Automotive

Simulating SMC part response with greater confidence using Digimat

Overview:

While Sheet Molded Compound (SMC) materials have been widely used in the automotive industry for some time, recently there has been a move to apply SMCs on more structurally demanding components. Though the material has long been considered quasi-isotropic with relative success, it has become apparent in industry that due to the complex manufacturing process, optimal structural design is not possible without considering the real anisotropic nature of the material.. With growing demand from the market, now is the time to leverage advanced SMC modeling capabilities targeting crash performance.

Results Validation:

Static and crash FEA simulations can now attain an excellent level of accuracy in stiffness and can capture peak load and displacement trends for typical part load cases.

The inner seat part illustrates the proposed workflow from process simulation to structural application. The Digimat simulation achieves a much better fit with respect to test data for most load cases, including head impact (puncture) and provide a good indication of hot spot localizations.


 
pdf iconDOWNLOADdown arrow

Company:

Robert Bosch Engineering and Solutions Pvt Ltd

Products:

Simufact Additive

Industries:

Additive Manufacturing

Bosch: Overcome additive manufacturing issues by process simulation

Challenge:

Avoid additive manufacturing issues (distortion, residual stress) and establish a “right first time” manufacturing process.

Solution:

Build process simulation helped Bosch to predict manufacturing issues and to find the right countermeasures to optimize the AM build process.


 
pdf iconDOWNLOADdown arrow

Company:

Vellore Institute of Technology

Products:

Adams
Adams Car

Industries:

Automotive

Improving Ride and Handling of Formula Student Car Using Adams Car

Challenge:

Zuura Formula Racing is a student team from the Vellore Institute of Technology in Chennai, India that participates regularly in the Formula SAE student competition organized across the globe by SAE Interna-tional.

For participating teams, the task at hand is to develop a small formula-style race car. Each student team designs, builds and tests a prototype based on a series of rules, aimed at ensuring on-track safety and promoting clever problem solving. The prototype is evaluated for its potential as a production item.

During the course of this project, one of the focus areas for the Zuura Formula Racing team was to ensure good suspension for their vehicle. To achieve this, they needed to ensure that the tires were as perpendicu-lar to the ground as possible to achieve maximum traction. The front geometry had to be designed such that it had a negative camber in jounce. This was an important factor in keeping the wheels perpendicular to the ground, and also to resist body roll.

The main target before the vehicle dynamics simulation engineer at Zuura Formula Racing was to improve the ride and handling of the vehicle by reducing yaw, pitch and roll rates.

Solution:

The Zuura Formula Racing team used the Adams Car software from MSC Software. Adams Car allows students to design and simulate their FSAE vehicles to maximize their vehicle performance. With Adams Car, FSAE teams can quickly build and test their functional virtual prototypes of complete vehicles and vehicle subsystems. FSAE engineering teams can exercise their vehicle designs under various road condi-tions, performing the same tests they normally run in a test lab or on a test track, but in a fraction of time.


 
pdf iconDOWNLOADdown arrow

Company:

Hyundai Motor Company

Products:

Actran Acoustics

Industries:

Automotive

Actran Helps Reduce Time to Optimize Design of Active Pedestrian Alerting System by 50%

Challenge:

Save time in finding the best Active Pedestrian Alerting System design without prototype

Solution:

Apply Actran to study complete speaker driver and its interactions with its acoustic environment


 
pdf iconDOWNLOADdown arrow

Company:

Hitachi Mito Engineering Co., Ltd.

Products:

PICLS

Industries:

Automotive

Real-time solutions for thermal problems

 
 
pdf iconDOWNLOADdown arrow

Company:

Murata Machinery, Ltd.R&D Headquarters, Kyoto, Japan

Products:

scPOST

Industries:

Automotive

Fluid analysis software helps visualize the unobservable space, shorten development time and demonstrate product mechanism

 
 
pdf iconDOWNLOADdown arrow

Company:

Payette

Products:

scPOST

Industries:

Automotive

The accurate CFD software that throttles up building design and energy modeling processes

 
 
pdf iconDOWNLOADdown arrow

Company:

Panasonic Corporation

Products:

scSTREAM | HeatDesigner

Industries:

Automotive

Thermal fluid analyses for the design of the world’s smallest optical disc drive - Applying to fuel cell systems and other energy products

 
 
pdf iconDOWNLOADdown arrow

Company:

Nikken Sekkei Ltd

Products:

scSTREAM | HeatDesigner

Industries:

Automotive

Corporate BIM strategies of an institutional architect office: assisting architectural designs with simulations using “scSTREAM”

 
 
pdf iconDOWNLOADdown arrow

Company:

Products:

scSTREAM | HeatDesigner

Industries:

Automotive

Using scSTREAM to evaluate airflow in production facilities improves the understanding and enables effective presentations

 
 
pdf iconDOWNLOADdown arrow

Páginas